product data sheet key features ? wide input ranges ? typical efficiency of 80% (76% for 3.3v) ? remote on/off ? overvoltage protection ? meets fcc section 15 sub part j class b radiated, class a conducted ? u.l., csa approved ? ce (lvd) applications ? telecommunications equipment ? digital circuits ? private branch exchange ? distributed power systems ? analog systems the 10 watt dc/dc converters operate from wide input ranges. a low profile makes them ideal for board-mounted applications where space is at a premium. available in single and dual outputs. general electrical specifications (specifications at nominal input and 25 c, nominal input voltage and rated output current unless other wise noted.) input specifications input voltage range see selection guide input filter pi type, lc on "aw" input current see selection guide input transient voltage 100 vdc for 100 ms. reverse voltage protection none startup & shutdown voltage (c), (cne), (sn) ? (30), (36) vdc start up time (power applied) (c), (cne), (sn) (<5 ms), (.25 to 15 ms) turn-on overshoot (10a48r5sn only) .25vdc (max) remote on/off enable inhibit, logic low start up time open circuit i sink < 0.1ma, < 0.5 vdc < 1ms 10 watt dc/dc converters www.datasheet.co.kr datasheet pdf - http://www..net/
product data sheet output specifications voltage variance/regulation (across: temp, input, & load range) single 3.3v, 5v, 6. 5 single 15v dual 5v, 12v, 15 v 4% 10% 4% ripple & noise 20 mhz bandwidth (sn) (c), (cne), or no letter duals 12, 5 100 mv p-p (max) 100 mv p-p (max) external .1mf cap 100 mv p-p (max) external 100mf caps. transient response (sn) 25% from 10% to 100% of rated load, 5% voltage deviation (c) & (cne) 25% from 50% to 90% of rated load, 5% voltage deviation < 0.3 ms., recovery time to 1% < 1.5 ms., recovery time to 1% load current maximum minimum see selection guide 10% of full load short circuit protection (sn), (c), (cne), or no letter continuous initiated between 105% and 200% of rated current. power output 10 watts continuous no derating to 71c no derating to 85c (sn) (c), (cne), or no letter overvoltage protection 6.2v on 5v unit; 4.3v on 3.3 v unit fcc sect. 15 sub part j yes general specifications isolation 1500 vdc operating temperature (sn) (c), (cne), o r no letter -25 to + 71c -40 to + 85c storage temperature (sn) (c), (cne), o r no letter -25 to +100c -40 to +100c fcc compliance class b radiated class a conducted efficiency 76% - 80% typical selection guide device type input volts vdc input current a (max) output voltage output current a (max) 10a24r5c 18-36 0.585 5.0 2.0 10a24r12c 18-36 0.585 12.0 0.83 10a24r15-15 12-48 1.070 15.0 0.334 10a48r3.3c 36-75 0.278 3.17-3.43 3.0 10a48r5c 36-75 0.278 4.80-5.20 2.0 10a48r5cne 36-75 0.278 4.80-5.20 2.0 10a48r3.3sn 36-75 0.281 3.17-3.43 3.0 10a48r5sn 36-75 0.278 4.80-5.20 2.0 10aw48r5 18-72 0.278 5.0 2.0 10aw48r5-5 18-72 0.278 5.0 1.0 10aw48r6.5t 18-72 0.265 6.5 1.54 10aw48r12-12 18-72 0.265 12.0 0.417 www.datasheet.co.kr datasheet pdf - http://www..net/
product data sheet pin connections: mechanical specification for " 10a" (dimensions in inches) pin connection 1 + v input 2 ? v input 3 + v output 4 no pin* 5 v return 6 enable** * dual output common *10a48r5cne pin 6 omitted pin connections mechanical specification for "10a w" (dimensions in inches) pin single output dual output 1 + input + input 2 - input - input 3 + output + output 4 no pin/adjust (5v only)* output common 5 output common - output * 5v output model may be ordered with adjust pin 4 (trim) by adding the suffix "t" reliability power locations headquarters & customer service sales reliability power, incorporated 33 musick irvine, ca 92618 usa tel: (949) 305-6700 fax: (949) 305-6701 www.reliabilitypower.com reliability power, incorporated attention: sales tel: (805) 449-1667 fax: (805) 557-4530 sales@reliabilitypower.com copyright? 2000-2006, reliability power inc. relia bility power inc. reserves the right to make change s in the product at any time, without notification. 10a-aw watt.doc 10 may 2006 notes (all devices and packages): 1. all dimensions in parentheses are metric 2. tolerances unless otherwise specified: .xx .03 (.76) .xxx .015 (.38) www.datasheet.co.kr datasheet pdf - http://www..net/
|
